Transition Networks Ethernet Point System 10BASE-T to 10BASE-FL Media Converter 1 x RJ-45 10Base-T , 1 x SC Duplex 10Base-FL - Media Converter

$141.99

Product Info

Transition Networks Ethernet Point System 10BASE-T to 10BASE-FL Media Converter

Item #:	EH10059947
Manufacturer:	Transition Networks, Inc
Mfr. Part #:	CETTF1013-105
Condition:	New
Price:	$141.99
Stock:	3284

General Information
Manufacturer	Transition Networks, Inc
Manufacturer Part Number	CETTF1013-105
Manufacturer Website Address	www.transition.com
Product Name	Ethernet Point System 10BASE-T to 10BASE-FL Media Converter
Marketing Information	Integrate mixed cabling environments using either switched or shared Ethernet. This full-featured media converter makes the migration from copper to fiber easier than ever before.
Product Type	Media Converter

Interfaces/Ports
Interfaces/Ports	1 x RJ-45 10Base-T Single Fiber 1 x SC Duplex 10Base-FL

Media & Performance
Connectivity Media	10Base-T Category 3, 5 UTP/STP 10Base-FL 850 nm Multi-mode Fiber
Distance Support	1.24 Mile Multi-mode Fiber 3936.96 " Category 3, 5 UTP/STP
Data Transfer Rate	10MBps Ethernet

Management & Protocols
Management	Using SNMP: Use SNMP at an attached terminal or at a remote location to: - Monitor media converter by monitoring: - Media Converter Power - Copper Link Status - Fiber Link Status - Copper Receive Status - Fiber Receive Status - Hardware Switch settings - Fault Conditiion Enter network commands that: - Enable/disable Fiber Port - Enable/disable Copper Port - Enable/disable AutoCross - Enable/disable LinkAlert - Power Down Media Converter
Protocols	Ethernet SNMP

Controls/Indicators
Status Indicators	Unit LED: Power: On for normal operation Port LEDs: LKF (Link Fiber): Steady LED indicates good fiber link and normal operation RXF (Receive Fiber): Flashing LED indicates data reception on fiber link LKC (Link Copper): Steady LED indicates good copper link and normal operation RXC (Receive Copper): Flashing LED indicates data reception on copper link

Power Description
Power Consumption	2.3 W Operating

Environmental Conditions
Temperature	32 °F (0 °C) to 140 °F (60 °C) Operating -4 °F (-20 °C) to 185 °F (85 °C) Storage
Humidity	10 to 90% Non-condensing Operating
Altitude	0 " to 120000 " Operating

Physical Characteristics
Dimensions	3.4" Height x 3.4" Width x 5" Depth
Shipping Dimensions	2.25" Height x 5" Width x 8.5" Depth
Weight	0.5 lb
Shipping Weight	1 lb

Miscellaneous
Additional Information	Operating temperature range for this Slide-In-Module depends on the physical characteristics and the installation configuration of the TRANSITION Networks chassis in which this Slide-In-Module will be installed. See the User's Guide for the chassis in which this Slide-In-Module will be installed for a discussion of temperature-related installation constraints. AutoCross: AutoCross technology eliminates an entire category of network troubleshooting by automatically matching crossed and uncrossed cables to the appropriate connection. The twisted pair port is instantaneously configured to the correct MDI or MDI-X configuration. LinkAlert: Because most Ethernet technologies are unable to recognize downlink faults, a failed link may appear normal to network management, requiring unnecessary time devoted to troubleshooting. LinkAlert monitors all physical uplink and downlink failures and enables all faults to be detected by network management. Fiber Optic Connector: Min TX PWR: -16.0 dBm Max TX PWR: -10.0 dBm RX Sensitivity: -29.5 dBm Max In PWR: -7.2 dBm Link Budget: 13.5 dB 3-position Jumper: Hardware: Converter mode is determined by 4-position switch settings. Software: Converter mode is determined by most recently saved on-board microprocessor settings. 4-position Switch: Fiber Port (UP = enabled): Enables/disables network traffic on the fiber port. Copper Port (UP = enabled): Enables/disables network traffic on the copper port. AutoCross (UP = enabled): Enables/disables the AutoCross function LinkAlert (UP = enabled): Enables/disables the LinkAlert function
Certifications & Standards	IEEE® 802.3 UL Listed C-UL Listed (Canada) CE Mark EN55022 EN55024 EN61000 FCC & CISPR Class A devices comply with radiated emissions standards for commercial applications in the United States (FCC Class A) FCC & CISPR Class B devices comply with radiated emissions standards for residential applications in the United States (FCC Class B)

Warranty
Standard Warranty	Lifetime Limited
Parts Warranty/Labor	- Lifetime
Additional Warranty Information	Effective for Products Shipped May 1, 1999 and After. Every Transition Networks' labeled product purchased after May 1, 1999 will be free from defects in material and workmanship for its lifetime. This warranty covers the original user only and is not transferable. This warranty does not cover damage from accident, acts of God, neglect, contamination, misuse or abnormal conditions of operation or handling, including over-voltage failures caused by use outside of the product's specified rating, or normal wear and tear of mechanical components. If the user is unsure about the proper means of installing or using the equipment, contact Transition Networks' free technical support services.

Reviews


There are currently no product reviews. Write a review on this product!

Manufacturer

Maunufacturer's Information
Other products

Extra Info

Product Reviews
There are currently no product reviews
Write a review on this product!

Additional Information
This product was added to our catalog on Thursday 06 March, 2008.
Notify me of updates to Transition Networks Ethernet Point System 10BASE-T to 10BASE-FL Media Converter
Tell someone you know about this product.